CV axle shaft clicking on turns or shaking under acceleration? Replace worn CV joints with a complete axle assembly built for smooth, confident power transfer.
SOLD
OUT
SOLD
OUT
SOLD
OUT
SOLD
OUTA CV axle shaft transfers drive torque while its joints accommodate suspension movement and, on driven steering axles, steering angles. Start a CV axle replacement by entering the exact year, make, model, trim, engine, transmission, and drive type. Then verify front or rear placement, driver or passenger side, quantity, and every application note. Similar-looking shafts can differ in length, joint design, splines, ABS provisions, and mounting details. Use the VIN when the selector presents more than one drivetrain or production option.
A CV axle shaft assembly may be sold as one side, a driver-and-passenger pair, or a front or rear set. Current A-Premium listings include a single front driver-side unit, paired front assemblies, and paired rear assemblies, so quantity and position need separate confirmation. Do not assume the left and right sides share dimensions or interchange.
Check whether the application is front-wheel drive, rear-wheel drive, all-wheel drive, or four-wheel drive, along with automatic or manual transmission notes. Some listed powersports axles also exclude lifted vehicles or particular suspension layouts. Treat each note as part of fitment, even when the year and model appear correct.
Clicking during turns, vibration under acceleration, or grease thrown around the joint area can justify inspection, but none of these observations alone proves the CV joint axle is defective. Check the boots for cuts, tears, punctures, missing or loose clamps, and visible grease slinging. On some applications, light surface grease may not indicate a torn boot; clean the area and inspect the boot and clamps before deciding on replacement.
Also inspect tires, suspension parts, axle fasteners, transmission or differential leaks, and the wheel hub bearing. Humming that changes with road speed may involve a bearing, while vibration can come from several rotating or supporting components. Confirm the source before buying a replacement CV axle assembly.
Use the vehicle selector, then read the product-page compatibility table and notes. Compare overall configuration, inner and outer joint ends, spline information when listed, ABS-related details, sealing surfaces, and included hardware with the removed axle. Chassis ranges, submodels, transmission type, and production dates can narrow fitment within the same model year.
If a vehicle has been lifted or modified, do not rely on stock fitment data without checking operating angles and the product restrictions. An altered ride height may place a CV axle outside the conditions covered by its listing. Contact support with the VIN and modification details when the product note does not resolve the question.
Support the vehicle safely and follow its service procedure for axle removal, seals, retaining hardware, and axle-nut tightening. Check the engine mount and transmission mounts if movement under load contributed to the complaint, but replace them only after inspection. After installation, confirm the axle is fully seated, boots are not twisted, clamps remain secure, and no fluid leaks or unusual noises appear during a controlled road check.
In shopping language, the terms often overlap. A complete axle assembly normally includes the shaft with inner and outer CV joints and boots, but confirm the listing photos and included components.
Usually not unless the product listing explicitly says so. The two sides can have different lengths, joint ends, splines, or support arrangements, so order by exact installation position.
Not automatically. Replace the axle that fails inspection unless wear, damage, or planned labor supports doing both. Inspect the opposite boots and joints before deciding.
No. Repeated turning clicks can support a CV-joint diagnosis, but wheel, suspension, steering, or fastener problems may produce similar sounds. Inspect and isolate the source first.
Enter the complete vehicle information and read the drive-type, transmission, position, and fitment notes. AWD and non-AWD shafts may differ even for the same year and model.
Repair CV axles if only the boot is damaged and joints are healthy. Replace the assembly for internal wear, binding, or shaft damage. Compare costs, labor, and safety to choose the right fix.
Fix transmission leaks after CV axle replacement by checking seal damage, axle seating, part fitment, and fluid levels. Learn to diagnose causes, avoid driving risks, and apply correct repairs to prevent transmission damage.
Replace your CV axle safely with this DIY guide. Learn to remove the old shaft, install the new one, and torque fasteners correctly. Includes essential tool lists, safety tips, and pre-drive checks to ensure a secure repair.
Diagnose bad CV axles by identifying clicking during turns, acceleration shudder, or grease leaks. Learn to distinguish inner vs. outer joint failures, inspect boots safely, and decide between boot kits or full axle replacement to avoid breakdowns.
In this guide, we break down the mechanical link between your suspension and drivetrain, revealing why maintaining your shocks is the ultimate insurance policy for your CV joints.
